RUT956 LTE Cat 4 Router (LATAM)
RUT956
ROUTER CELULAR INDUSTRIAL
El RUT956 es un router industrial que combina opciones de conectividad móvil, Wi-Fi y por cable con funciones de conmutación automática por error de WAN y GNSS. Las interfaces de comunicación serie permiten integrar dispositivos más variados en el ecosistema de soluciones, mientras que las E/S y el software avanzado RutOS facilitan el control de equipos, la automatización y las notificaciones de eventos.
-
FREQUENCY
4G (LTE-FDD): B1, B2, B3, B4, B5, B7, B8, B28
4G (LTE-TDD): B40
3G: B1, B2, B4, B5, B8
2G: B2, B3, B5, B8
RUT956
ROUTER CELULAR INDUSTRIAL
El RUT956 es un router industrial que combina opciones de conectividad móvil, Wi-Fi y por cable con funciones de conmutación automática por error de WAN y GNSS. Las interfaces de comunicación serie permiten integrar dispositivos más variados en el ecosistema de soluciones, mientras que las E/S y el software avanzado RutOS facilitan el control de equipos, la automatización y las notificaciones de eventos.
-
MOBILE
- Mobile module
4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps
- SIM switch
2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection
- Status
Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID
- SMS
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
- USSD
Supports sending and reading Unstructured Supplementary Service Data messages
- Black/White list
Operator black/white list
- Multiple PDN
Possibility to use different PDNs for multiple network access and services
- Band management
Band lock, Used band status display
- APN
Auto APN
- Bridge
Direct connection (bridge) between mobile ISP and device on LAN
- Passthrough
Router assigns its mobile WAN IP address to another device on LAN
WIRELESS
- Wireless mode
IEEE 802.11b/g/n, Access Point (AP), Station (STA)
- WiFi security
WPA2-Enterprise - PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation
- SSID/ESSID
SSID stealth mode and access control based on MAC address
- WiFi users
Up to 100 simultaneous connections
- Wireless Hotspot
Captive portal (Hotspot), internal/external Radius server, built in customizable landing page
ETHERNET
- WAN
1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
- LAN
3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX
NETWORK
- Routing
Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, NHRP)
- Network protocols
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)
- VoIP passthrough support
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets
- Connection monitoring
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
- Firewall
Port forward, traffic rules, custom rules
- DHCP
Static and dynamic IP allocation, DHCP Relay, Relayd
- QoS / Smart Queue Management (SQM)
Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
- DDNS
Supported >25 service providers, others can be configured manually
- Network backup
WiFi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover
- Load balancing
Balance Internet traffic over multiple WAN connections
- Hotspot
Captive portal (Hotspot), internal/external Radius server, SMS authorization, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customizable themes
- SSHFS
Possibility to mount remote file system via SSH protocol
SECURITY
- Authentication
Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block
- Firewall
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
- Attack prevention
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
- VLAN
Port and tag based VLAN separation
- Mobile quota control
Custom data limits for both SIM cards
- WEB filter
Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
- Access control
Flexible access control of TCP, UDP, ICMP packets, MAC address filter
VPN
- OpenVPN
Multiple clients and a server can run simultaneously, 27 encryption methods
- OpenVPN Encryption
DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,
BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
- IPsec
IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)
- GRE
GRE tunnel, GRE tunnel over IPsec support
- PPTP, L2TP
Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support
- Stunnel
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
- DMVPN
Method of building scalable IPsec VPNs
- SSTP
SSTP client instance support
- ZeroTier
ZeroTier VPN client support
- WireGuard
WireGuard VPN client and server support
- Tinc
Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.
MODBUS TCP SLAVE
- ID range
Respond to one ID in range [1;255] or any
- Allow Remote Access
Allow access through WAN
- Custom registers
MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality
MODBUS TCP MASTER
- Supported functions
01, 02, 03, 04, 05, 06, 15, 16
- Supported data formats
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)
MODBUS RTU MASTER (RS232)
- Supported baud rates
From 300 to 115200
- Supported functions
01, 02, 03, 04, 05, 06, 15, 16
- Supported data formats
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
- Number of data bits
From 5 to 8
- Number of stop bits
1 or 2
- Parity
None, Even, Odd
- Flow
None, RTS/CTS, Xon/Xoff
- Duplex
Full duplex
MODBUS RTU MASTER (RS485)
- Supported baud rates
From 300 to 300000
- Supported functions
01, 02, 03, 04, 05, 06, 15, 16
- Supported data formats
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII
- Number of data bits
8
- Number of stop bits
1
- Parity
None, Even, Odd
- Flow
None, Xon/Xoff
- Duplex
Half duplex
MODBUS DATA TO SERVER
- Protocol
HTTP(S), MQTT, Azure MQTT
MQTT GATEWAY
- MQTT Gateway
Allows sending commands and receiving data from MODBUS Master through MQTT broker
DNP3
- Supported modes
TCP Master, DNP3 Outstation, RTU Master
MONITORING & MANAGEMENT
- WEB UI
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
- FOTA
Firmware update from server, automatic notification
- SSH
SSH (v1, v2)
- SMS
SMS status, SMS configuration, send/read SMS via HTTP POST/GET
- Call
Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, WiFi on/off
- TR-069
OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
- MQTT
MQTT Broker, MQTT publisher
- SNMP
SNMP (v1, v2, v3), SNMP Trap
- JSON-RPC
Management API over HTTP/HTTPS
- MODBUS
MODBUS TCP status/control
- RMS
Teltonika Remote Management System (RMS)
IOT PLATFORMS
- Cloud of Things
Allows monitoring of: Device data, Mobile data, Network info, Availability
- ThingWorx
Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
- Cumulocity
Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength
- Azure IoT Hub
Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type
SYSTEM CHARACTERISTICS
- CPU
Mediatek MIPS 24Kc 580 MHz
- RAM
128 MB, DDR2
- FLASH storage
16 MB, SPI Flash
FIRMWARE / CONFIGURATION
- WEB UI
Update FW from file, check FW on server, configuration profiles, configuration backup
- FOTA
Update FW
- RMS
Update FW/configuration for multiple devices at once
- Keep settings
Update FW without losing current configuration
FIRMWARE CUSTOMIZATION
- Operating system
RutOS (OpenWrt based Linux OS)
- Supported languages
Busybox shell, Lua, C, C++
- Development tools
SDK package with build environment provided
LOCATION TRACKING
- GNSS
GPS, GLONASS, BeiDou, Galileo and QZSS
- Coordinates
GNSS coordinates via WebUI, SMS, TAVL, RMS
- NMEA
NMEA 0183
- NTRIP
NTRIP protocol (Networked Transport of RTCM via Internet Protocol)
- Server software
Supported server software TAVL, RMS
- Geofencing
Configurable multiple geofence zones
SERIAL
- RS232
DB9 connector, full RS232 (with RTS, CTS)
- RS485
RS485 Full Duplex (4 wires) and Half Duplex (2 wires). 300-115200 baud rate
- Serial functions
Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client
USB
- Data rate
USB 2.0
- Applications
Samba share, USB-to-serial
- External devices
Possibility to connect external HDD, flash drive, additional modem, printer
- Storage formats
FAT, FAT32, NTFS
INPUT / OUTPUT
- Input
1 x digital dry input (0 - 3 V), 1 x digital galvanically isolated input (0 - 30 V), 1 x analog input (0 - 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 - 5 V detected as logic low, 8 - 30 V detected as logic high)
- Output
1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector)
- Events
Email, RMS, SMS
- I/O juggler
Allows to set certain I/O conditions to initiate event
POWER
- Connector
4-pin industrial DC power socket
- Input voltage range
9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max
- PoE (passive)
Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 - 50 VDC
- Power consumption
< 2 W idle, < 7 W Max
PHYSICAL INTERFACES
- Ethernet
4 x RJ45 ports, 10/100 Mbps
- I/O’s
2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connector (available from HW revision 1600)
- Status LEDs
1 x bi-color connection status LED, 5 x connection strength LEDs, 4 x LAN status LEDs, 1 x Power LED
- SIM
2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional)
- Power
1 x 4-pin power connector
- Input/output
1x 10 pin industrial socket for inputs/outputs
- Antennas
2 x SMA for LTE, 2 x RP-SMA for WiFi, 1 x SMA for GNSS
- USB
1 x USB A port for external devices
- RS232
1 x DB9 socket
- RS485
1 x 6-pin industrial socket
- Reset
Reboot/User default reset/Factory reset button
PHYSICAL SPECIFICATION
- Casing material
Aluminium housing, plastic panels
- Dimensions (W x H x D)
110 x 50 x 100 mm
- Weight
287 g
- Mounting options
DIN rail (can be mounted on two sides), flat surface placement
OPERATING ENVIRONMENT
- Operating temperature
-40 °C to 75 °C
- Operating humidity
10% to 90% non-condensing
- Ingress Protection Rating
IP30
REGULATORY & TYPE APPROVALS
- Regulatory
CE/RED, UKCA, CB
EMI IMMUNITY
- Standards
EN 301 489-1 V2.2.3, EN 301 489-17 V3.2.4, Draft EN 301 489-19 V2.2.0, Final draft EN 301 489-52 V1.2.0, EN 55032:2015+A1:2020, EN 55035:2017+A11:2020, EN 61000-3-3:2013+A1:2019, EN IEC 61000-3-2:2019
- ESD
EN 61000-4-2:2009
- RS
EN 61000-4-3:2020
- EFT
EN 61000-4-4:2012
- Surge immunity (AC Power Line)
EN 61000-4-5:2014+A1:2017
- CS
EN 61000-4-6:2009
- DIP
EN IEC 61000-4-11:2020
PERFORMANCE SPECIFICATIONS
- Standards
EN 300 328 V2.2.2, EN 301 908-1 V13.1.1, EN 301 908-2 V13.1.1, EN 301 908-13 V13.1.1, EN 303 413 V1.1.1
SAFETY
- Standards
EN IEC 62311:2020
AS/NZS 60950.1:2015
IEC 62368-1:2018,
EN IEC 62368-1:2020+A11:2020
No customer reviews for the moment.